Multifunction DC10G DC10K Generator Set Controller Engine Manual Start Stop Controller(Silver)

Electronic Engine ControlMultifunction DC10G DC10K Generator Set Controller engine manual start and stop controllerDescription:The DC10G is a controller for manual start and stop of the engine. The 4-bit LED digital tube displays the generator set frequency, voltage, battery voltage, and accumulated working time. It has various parking protection and alarm indication functions, which can conveniently monitor the working status of the generator set.The controller can be connected to the computer through the data line, and the controller parameters can be set by software to easily match the generator set of more specifications.DC10G/DC10K: the similar function, just different wiringPanel introduction:1. IndicatorsGen frequencyOver/under speedGen voltageLow oil pressureBattery voltageHigh water temperatureAccumulated timeCharging abnormalEmergency stopOver voltageNote:1) Over speed value will be displayed by flashes after over speed alarm.2) Over voltage value will be displayed by flashes after over voltage alarm.3) Charge failure will be displayed as alarm indication but will not stop the engine.2. Buttons introductionDisplay buttons:Four status switch (gen voltage, gen frequency, battery voltage, accumulated time).Press the PAGE button in 5 sec above under Module on power but stop mode,the frequency can be switched between 50Hz and 60Hz.Operation:1. Power on : Switch "0"to "I" till the tube is lighted, In the procession of cranking, over speed indicator will be lighted if the crank is not successful after 45sec.(controller will cut off fuel solenoid's output and come into protection)2. Start running: Switch "I " to "II" till engine started. Once power on the engine, it will be cranked. the controller will come into running status after 8 sec if cranking successfully. Then the controller will monitor the relative parameters and set protection.(the controller will cut off fuel solenoid output and display the alarm status if the genset is stopped.)Please Switch from "I"to "0".3. Stop and reset:Switch from "I"to "0" and take off the power.Parameter setting:Please connect the module to PC by communication cables and powered on.1. Alarm settingOver speed alarm: 1710RPM(Rated 50Hz), 2040RPM(Rated 60Hz), range: 0-4000RPM, when the RPM is over this value and keep more than 1sec, then the controller will alarm and stop.Over frequency alarm: 57Hz(Rated 50Hz), 68Hz(Rated 60Hz),range:40-80Hz, when the frequency is over this value and keep more than 1 sec, then the controller will alarm and stop.Low frequency alarm: 20Hz, range: 20-60Hz,when the frequency is lower than the value and keep more than 5sec, the controller will alarm and stop.Over voltage alarm: 500V, range:50-500v, 500V is set as forbidden. When the voltage is over this value and keep more than 5sec,then the controller will alarm and stop.Charging failure D- value:6V,range:1-24V, when the different value between charging D+ and Battery B+ is over this value and keep more than 5sec, then the controller will alarm.2. Display settingFour Screen self-cycling display: the parameters shall be switched timely according to the interval time setting after choosing this option.Homepage option: one parameter can be displayed as homepage display after choosing this function. The page will be switched automatically after pressing page change button for a while.Revert-back delay: the time to revert back to homepage.Self-cycling display time: the interval time setting.Technical Specifications:Power supply:8-33VDCPower consumption:MAX 2W(WorkingAlternator Voltage input:15-300VAC,50/60HSpeed input:Freq 300Hz-10kHFuel output:MAX 16Start output:MAX 10Excitation Output:MAX 80mAlarm output:MAX 16Operating temperature:-30-75Storage temperature:-40-85Dimensions:78×78×72mPannel cutout:67×67mWeight:280gNote:- Due to lighting effects, monitor's brightness , contrast settings etc, there could be some slight differences in the color tone of the pictures and the actual item.

• Electronic Engine Control
• Multifunction DC10G DC10K Generator Set Controller Engine Manual Start Stop Controller